THE RIGHT STUFF / L’ETOFFE des HEROS
Captain Charles « Chuck » YEAGER broke the sound barrier with the help of his friend Jack RIDLEY on a 14th of October 1947 – He did it 61 years ago!
(U. S. Air Force illustration/Mike Carabajal)
Photo: U.S.Air Force Link
XLR-11 ROCKET POWERED AIRCRAFT
Birth of Manned Rocket Research Airplanes: 1946 to 1975
The first reliable, effective rocket engine that would provide boost for experimental research aircraft was produced by four members of the American Rocket Society (ARS) who combined forces to form Reaction Motors Incorporated (RMI) (Rockaway, New Jersey) for developing the Experimental Liquid Rocket (XLR-11) rocket motor. The XLR-11 engine had four separate rocket chambers. Each chamber provided 1500 lb of rated thrust and could be operated independently as a means of throttling thrust in quarters, up to 6000 pounds. The XLR-11 possessed remarkable longevity, powering an impressive fleet of rocket aircraft for more than a quarter of a century (1946 to 1975). This fleet of vehicles were the first rocket aircraft devoted solely to high performance experimental flight research. They were not constrained by military or commercial demands and ranged from being the first to break the sound barrier (XS-1), to the first to reach Mach 2.0 (D-558-II [fig. 5]), to the first to exceed the X-2 Mach 3.2 record (X-15 with two XLR-11 engines).
Figure 5. The D-558-II airplane on Rogers lakebed.
The X-1E – Early Development of Energy Management
Design efforts to extend aircraft performance produced increased wing loadings, W/S, and decreased lift-to-drag ratios, L/D. These design changes were beneficial in reducing drag to achieve supersonic and hypersonic speeds, but were also detrimental in that they reduced the area of the maneuvering footprint and presented difficulties in the approach and landing.
As L/D values decreased, the glide slope angle and the rate of descent increased, making it more difficult for pilots to estimate distances and times required for acceptable landings. The X-1E (fig. 6) was modified with a low-aspect-ratio wing having a thickness-to-chord ratio of four percent – the only aircraft of the X-1/D-558 series to have sufficiently low L/D values to require unique energy management techniques. This X-1E was the first to experiment with approach patterns designed to give
the pilot more time in the traffic pattern to manage energy.
The landing pattern was approached in a conventional manner except that altitudes and speeds were somewhat higher than for
powered aircraft. The initial reference point was established at 12,000 ft (mean sea level) on a downwind heading (180 deg remaining to turn). The downwind leg was offset some four miles from the centerline of the landing runway. On downwind, abeam the touchdown point, landing gear and partial flaps were deployed at a speed of 240 knots. Full flaps were usually deployed on the final approach. At the initial reference point the pilot had almost three minutes until touchdown – additional time for handling increased speeds and sink rates.7,8
Figure 6. The X-1E airplane on Rogers lakebed.
Report from www.archives.gov
(Text from the NASA at: http://www.nasa.gov/centers/dryden/home/index.html)
A program conducted between 1979 and 1982 at the NASA Dryden Flight Research Center, Edwards, Calif., successfully demonstrated an aircraft wing that could be pivoted obliquely from zero to 60 degrees during flight. The unique wing was demonstrated on a small, subsonic jet-powered research aircraft called the AD-1 (Ames Dryden -1). The aircraft was flown 79 times during the research program, which evaluated the basic pivot-wing concept and gathered information on handling qualities and aerodynamics at various speeds and degrees of pivot.
The oblique wing concept originated with Robert T. Jones, an aeronautical
engineer at NASA’s Ames Research Center, Moffett Field, Calif.
Analytical and wind tunnel studies Jones initiated at Ames indicated that a transport-size oblique-wing aircraft, flying at speeds up to Mach 1.4 (1.4 times the speed of sound), would have substantially better aerodynamic performance than aircraft with more conventional wings. At high speeds, both subsonic and supersonic, the wing would be pivoted at up to 60 degrees to the aircraft’s fuselage for better high-speed performance. The studies showed these angles would decrease aerodynamic drag, permitting increased speed and longer range with the same fuel expenditure. At lower speeds, during takeoffs and landings, the wing would be perpendicular to the fuselage like a conventional wing to provide maximum lift and control qualities. As the aircraft gained speed, the wing would be pivoted to increase the oblique angle, thereby reducing the drag and decreasing fuel consumption. The wing could only be swept in one direction, with the right wingtip moving forward.
The AD-1 aircraft was delivered to Dryden in February 1979. The Ames Industrial Co., Bohemia, N.Y., constructed it, under a $240,000 fixed-price contract. NASA specified the overall vehicle design using a geometric configuration studied by the Boeing Commercial Airplane Company, Seattle, Wash. The Rutan Aircraft Factory, Mojave, Calif., provided the detailed design and load analysis for the intentionally low-speed, low-cost airplane. The low speed and cost of course limited the complexity of the vehicle and the scope of its technical objectives.
Piloting the aircraft on its first flight Dec. 21, 1979, was NASA research pilot Thomas C. McMurtry, who was also the pilot on the final flight Aug. 7, 1982. Powered by two small turbojet engines, each producing 220 pounds of static thrust at sea level, the aircraft was limited for reasons of safety to a speed of about 170 mph. The AD-1 was 38.8 feet in length and had a wingspan of 32.3 feet unswept. It was constructed of plastic reinforced with fiberglass, in a sandwich with the skin separated by a rigid foam core. It had a gross weight of 2,145 pounds, and an empty weight of 1,450 pounds. A fixed tricycle landing gear, mounted close to the fuselage to lessen aerodynamic drag, gave the aircraft a very « squatty » appearance on the ground. It was only 6.75 feet high. The wing was pivoted by an electrically driven gear mechanism located inside the fuselage, just forward of the engines.
Read full article on the NASA (www.nasa.gov) website: NASA Dryden Past Projects: AD-1 Oblique Wing – updated August 12, 2009
Michel Fournier tested his radio connection that also will ensure physiological monitoring, as a video connection through the helmet onboard his « gondola » was tested too. Everything looked OK, but the weather compelled to postpone the Frenchman’s feat a bit later. Now it looks OK again.
64-year old parachutist Michel FOURNIER should presently jump at a speed of 1.4 Mach at Flight Level 1320 (about 40 km, or 132,000 ft), almost over the ozone layer !!!
GO MICHEL ! GO and make a historical sonic boom as Chuck Yeager did!
The balloon is being inflated. Wait and see…