Foreign Object Damage (FOD) can be caused by Foreign Object Debris (called FOD too). FOD can also mean « Foreign Object Detection« . Watch the video, and read its transcript below:

Transcript :

Our Air Force has the most technically advanced aircraft in the world – deadly fighters, and bombers, mighty cargo and tanker workhorses, our many helicopters, and a variety of specialty aircraft.

But they can all be easily grounded by FOD.

Foreign objects cause damage to our aircraft in many ways. For example, cut tires, and jammed flight or engine controls. FOD has caused at least six fighter aircraft to crash over the last twelve years! Some of the items that caused these mishaps were:

• Rags;
• Safety wire pliers;
• A piece of aluminum foil;
• A one-inch piece of safety wire;
• Even a small washer!

These incidents show that poor housekeeping, and work practices are still the two major contributors to preventable FOD. We can eliminate FOD. To do so, we must make these six commonsense steps, part of our every job, every step, every day.

1. The first step – be aware that you can make a difference, and that FOD is a constant problem. Every time you sign out a tool box, work a job, or just step out to help someone, keep your eyes open for tools, rocks, and other debris. And when you see something, stop, and pick it up. Occasionally, you may need a sweeper to clean up an area. MAC usually coordinate with base OPS. MAC (Military Airlift Command) usually coordinates this support with base OPS.
2. The second step – keep your work area clean. Check your shoes for foreign objects, and empty your pockets of keys, change, pencils, and trash. Place these items into a FOD bag before entering the cockpit, intake, other confined areas, or before working on top of the aircraft. Are you covering all of those lines, houses, cannon plugs, and ducts during extended maintenance? The ACES II ejection seat is the most reliable, and safest seat in the world, as long as nothing gets in the way. Somebody did not report losing this pencil tip. It then migrated in flight to the sequence start switch which activates the seat computer as it departs the aircraft. It was discovered during a visual inspection of the seat when it was removed for other maintenance. Because of the protective shield over the switch, and the tight clearance in the cockpit, it normally would never have been found. How do you think the pilots felt when they heard about it? Do you check the area one more time before you leave? It is possible the person before you left something behind.
3. Step three – we have to keep our vehicles clean. We know foreign objects get around, and many times are, vehicles carry them out to the flight line. Tire checks – are you constantly doing them every time you went to the flight line? How about after you drove out of the taxiway to let the jet pass? How clean is your vehicle? Is there safety wire, trash, or fasteners on the floor? Is the FOD can overflowing before you empty it? If you have a vehicle magnet installed, are you checking it daily?
4. Step four – Thorough FOD walks. Are you looking, or are you out there just stretching your legs? Pay special attention to the grounding points, and cement grooves, and cracks. These areas are always filling up with trash, rocks, and hardware. A good daily FOD walk helps us keep up with all the debris that still manages to get onto the ramp. A FOD walk should have found this bolt. Instead, it was sucked up, off of the ramp by a B-1. Three first-stage compressor blades, and one inlet guide vane were damaged. It cost us 56 man-hours, and over $ 35,000 to remove and fix this engine.
5. Step five – good tool and hardware control is a must. Remember the last time you lost a tool, or a nut? How long did you look for it? Did you find it? When was the last tool report started? Remember – tool control starts when you receive a toolbox. Before you sign for it, make sure all missing tools are written up, and check the box for pieces of safety wire, and other trash. Woe! Slow down, and look. Is that a tool, or the tool cutout? If you find a tool missing, don’t accept the box, and make sure a last tool report, and investigation is started. Also, never leave tools in hardware in or on the aircraft. Do a good inventory of your toolbox, and TOs* after every job. This alone will narrow the search area, and greatly increase your chances of finding a last tool. Think about it, what would you rather check? One aircraft, or three? When you do find a tool missing, start looking for it immediately. If you can find it after a short search, report it immediately to the expediter, or dock chief, and get some extra help to look for the missing tool or hardware. For tight or inaccessible areas, you can also use a borescope** or X-ray equipment to locate lost items. How would you tell the pilot if the jet has just taxied? What if it is flying? A file about this size was left behind after blunting two engine blades on a C-5, possibly fallen behind a nacelle blocker door*** during the job. Four people then signed for the box over the next several days before someone finally noticed, and reported the last tool. The file was not located, and then came loose in flight the next day. This incident caused over 550 men-hours of work, and $ 66,000 in damage to the engine. Hardware control is simply taking only what you need, and counting how many nuts, bolts, or other hardware you take from bench stock. After the job, make sure you account for all the hardware. If you don’t complete the job, annotate the screw bag with the quantity, the type of hardware, and your name. This will help the person who finishes the job track down any missing hardware. Here is what a misplaced ¼ inch nut did to a C-130 engine. Over 30 blades were damaged beyond repair, not counting depot costs – the damages have already taken 64 man-hours, and exceeded $ 38,000 in damages. Sometimes, we accidentally leave items inside the intake danger area, or in the intake before an engine start. These have included VTR tapes, flashlights, cleaning bottles, and aircraft forms. Are you paying attention? Or have you just been lucky?
6. Step six – follow the T.O..

   For tight or inaccessible access areas, you can also use a borescope, or X-ray equipment to locate lost items. How would you tell the pilot if the jet has just taxied? What if it is flying? A file about this size was left behind after blending two engine blades on a C-5, possibly fallen behind a nacelle blocker door*** during the job. Four people then signed for the box over the next several days before someone finally noticed, and reported the last tool. The file was not located, and then came loose in flight the next day. This incident caused over 550 men-hours of work, and $ 66,000 in damage to the engine. Hardware control is simply taking only what you need, and counting how many nuts, bolts, or other hardware you take from bench stock. After the job, make sure you account for all the hardware. If you don’t complete the job, annotate the screw bag with the quantity, the type of hardware, and your name. This will help the person who finishes the job track down any missing hardware. Here is what a misplaced ¼ inch nut did to a C-130 engine. Over 30 blades were damaged beyond repair, not counting depot costs – the damages have already taken 64 man-hours, and exceeded $ 38,000 in damages. Sometimes, we accidentally leave items inside the intake danger area, or in the intake before an engine start. These have included VTR tapes, flashlights, cleaning bottles, and aircraft forms. Are you paying attention? Or have you just been lucky?

6. Step six (again and further) – Follow the T.O.. Several times we have had equipment, and panels come off during an engine run, or in flight, causing serious damage. On the last job before a three-day weekend, an experienced crew chief and his assistant were preparing an F-16 for an engine run. He skipped the warning, and the step to check the run screen safety pin for security. During the engine run, one pin came out, and after whipping around in the intake for a few seconds, the lanyard broke. The pin destroyed over 426 blades. Total cost – $ 69,000 and 366 man-hours. What was the cost of the crew chief? How do you think he felt? Think of what he went through. The de-certification, the investigation, the waiting. Was the two or three seconds saved worth it? Sometimes, confusing or incomplete TOs are part of the problem. Improper installation caused by poor tech aide, and inexperience created a stress crack in the upper anti collision light lens in a KC-10.

* T.O.: Technical Order

** (or boroscope)

*** Thrust reverser (pelle d’inverseur de poussée)

The post Foreign Object Damage and FOD Prevention appeared first on AVIATION ENGLISH.

Colonel Gagarin and his instructor Vladimir Seryogin (as Gagarin, director of the Star City, had to obtain his fighter pilot rating again), flew a MiG-15 Midget that day, and they should not have kept the fuel tanks under their jet. As the spin turned into a deadly crash, it has been suggested since 1986 that the afterburner turbulence of a Sukhoi Su-11 Fishpot-C interceptor aircraft could have caused the MiG-15 to go out of control.

The MiG-15 had first been designed to intercept USAF nuclear-capable B-29s.

Some governmental documents were declassified in 2003. They revealed that in addition to the official investigations, the KGB tried to advance a new line of inquiry. Since then, it has been deemed that the accident could not be due to any conspiracy theory. Though little is certain about this mistery, you can click on the frame below to read further information:

The post Enigma of Yuri Gagarin’s death on March 27 – 43 years ago appeared first on AVIATION ENGLISH.

On 6 December 2010, Continental Airlines was found criminally responsible for the disaster by a Parisian court and was fined € 200,000 and ordered to pay Air France € 1 million. Continental mechanic John Taylor was given a 15-month suspended sentence, while another airline operative and three French officials were cleared of all charges. The court ruled that the crash resulted from a piece of metal from a Continental jet that was left on the runway; the object punctured a tyre on the Concorde and then ruptured a fuel tank. Another Continental employee, Stanley Ford, was found not guilty. Continental’s lawyer, Olivier Metzner, said it would appeal the verdict.

The court also ruled that Continental would have to pay 70% of any compensation claims. As Air France has paid out € 100 million to the families of the victims, Continental could be made to pay its share of that compensation payout. Source – Wikipedia

The post Flight safety in question after guilty verdict in Concorde crash appeared first on AVIATION ENGLISH.

The post Ash could ground flights again… appeared first on AVIATION ENGLISH.

The post Pilots training through simulated ash clouds appeared first on AVIATION ENGLISH.

The post Airliner severe problems in volcanic dust appeared first on AVIATION ENGLISH.

The post Volcanic ash – Flight hazard explained appeared first on AVIATION ENGLISH.

The post Huge cloud still endangering European airspace – Pilot who flew through ash in 1982 reports appeared first on AVIATION ENGLISH.

17/03/2010
Certification tests of Russia’s new Sukhoi Superjet 100 medium-haul airliner are nearing completion. Its engine was subjected to tough reliability tests involving simulated ice and hail storms and frozen-carcass bird strikes.

www.rian.ru courtesy

The post SNECMA / NPO Saturn’s PowerJet SaM146 certification – Sukhoi Superjet 100 engine appeared first on AVIATION ENGLISH.

The post Hudson river ditching – January 15, 2009 appeared first on AVIATION ENGLISH.

The post The citizens of Danville, California honor their hero Chesley « Sully » Sullenberg, the flight 1549’s pilot appeared first on AVIATION ENGLISH.

The post NEW HUDSON JET WATER-LANDING VIDEO appeared first on AVIATION ENGLISH.

The post Pilots simulate Chesley Sullenberg’s feat – ditching into Hudson river appeared first on AVIATION ENGLISH.

It has happened today: a commercial aircraft – US Airways jet (A320) – has been compelled to land or ditch into the Hudson river as you can see on the last three videos. The aircraft has lost both engines after passing into a flock of birds. The pilot then carried out a perfect – as smooth as possible – ditching. Just a leg broken reported, a few injuries, nothing more even though the passengers had to walk along the wings in the frigid waters… That is the good news of the day!

Very special thanks to « Chacko » who added further information in the comments: « This guy Chelsey B. « Sully » Sullenberger, who put the plane in the water today is is an US Air Force Academy graduate who served in the Air Force from 1973 to 1980. He was an U.S. Air Force F-4 Phantom II fighter pilot who served as a flight leader and training officer in Europe and the Pacific. He was also the Blue Force mission commander during Red Flag exercises at Nellis Air Force Base, Nev. This is as per the USAF press service. »

The post THANKS TO GIFTED PILOT ALL PASSENGERS AND CREW HAVE SURVIVED ! appeared first on AVIATION ENGLISH.

Taken from The New York Times: http://www.nytimes.com

The post Anti Foreign Object Debris (FOD) contraption tested by the FAA appeared first on AVIATION ENGLISH.